Cryomax+ is the latest slimming system which adopt 4 advanced technology in 1 system: cryolipolysis, cavitation, lipo laser and RF energy. It treats all the body fat area in non invasive way, makes your body slimming, shaped smooth effortless and effective.
Cryolipolysis also called ‘fat freeze method’ for short. (cryo – cold, lipolysis – the breakdown of triglycerides into free fatty acids within cells. This non-invasive ‘cold’ technology cools the adipose tissue to induce lipolysis reducing body fat without damaging other tissues.
How does Cryomax+ Work?
Cryolipolysis for Fat Freezing
Cryolipolysis works by freezing fat cells to the point of natural elimination. The cold temperature breaks down the fat cells and the body naturally eliminates them. While the fat cells are destroyed, the surrounding skin and structures remain safe and free of injury. If you are struggling with fat bulges or have excess fat despite having followed a diet and exercise plan, you may be a good candidate for Cryolipolysis. The overall goal of the fat freeze procedure is to reduce the volume of the fat bulges resulting in a slimmer and more contoured body figure.
Lipolaser for Fat Melting
Lipolaser utilizing the power of 40mw-100mw diode laser, the most suitable to physical fat reduction, the 650nm diode laser deep blasts excess fat and melted emits low levels of laser energy, which creates a chemical signal in the fat cells, breaking down the stored triglycerides into free fatty acids and glycerol and releasing them though channels in the cell membranes. The fatty acids and glycerol are then transported around the body to the tissues that will use them during metabolism to create energy.
Cavitation for Fat Blast
Cavitation emits a powerful double beam of low-frequency modulated ultrasound waves on a 1 MHz carrier, produce a cavitation effect that damages the adipose cells causing them to gradually break up. The handpiece uses vacuum technology which lifts the adipose tissue on which the ultrasounds will act, preserving the underlying tissues and thus enhancing the effectiveness and safety of the treatment which focuses only on the area involved. The major reduction effect that can be achieved on localized adiposity and cellulite is given by the cavitation phenomenon, provided that the treatment is performed with low-frequency ultrasounds and adequate power
RF for facial rejuvenation and tightening
Use the bipolar and six polar RF technology, with output frequency 5.0 MHz, power 150watts, it transfers most RF energy to your dermis skin, effectively stimulates collagen and elastin production.
Functions
Key Features
· Immediate results
· Long-lasting results
· Fat reduction
· Visibly improved cellulite
· Comfortable
· No surgery
· No downtime
· Non-invasive
· Short treatment times
· No anesthesia
Advantages
1. Cryolipolysis, Cavitation, lipolaser and RF, 4 slimming technology in 1 machine
2. User-friendly, Cryolipolysis handpiece design with 7 different size replacement cup to treat body area, the extra chin handpiece is supplied to treat double chin. Contact cooling area updated to 360°full contact, more area can be treatment within 1 session.
3. Focused cavitation for larger fat area treatment and better slimming result
4. Total 8 lipolaser pads cover all body fat area, reduce fat effortless.
5. Different RF handle for face and body tighten.
6. The super cooling system with condenser ensure long continuous working at least 5 hours cryolipolysis treatment.
7. The high efficacy, ease of use, and cutting-edge technology provide a strong ROI on fat removal investment.
Interface Introduction
Parameters
|
Cooling Handle Size |
Big handpiece 23cm*7cm, 23cm*7cm, 20cm*7cm, 18cm*7cm Small handpiece 15cm*6cm, 15cm*6cm, 13cm*6cm Chin handpiece 8.5cm*4.3cm |
|
Cooling Device Output Temperature |
0,-5,-10 ℃ |
|
Vacuum Pressure |
0-80kpa |
|
Laser Wavelength |
Laser diode AlGalnp 635-650nm |
|
Max Lipolaser Output Power |
6000mw |
|
Lipolaser Power |
100mw/pcs |
|
Number of Diode Laser |
60 |
|
Cavitation Modulation Frequency |
40KHZ |
|
Max Cavitation Energy Density |
3W/cm2 |
|
RF Frequency |
5MHz |
|
RF Power |
150W |
|
Cooling System |
Wind+water+semiconductor |
|
Screen |
10.4 inch color touch screen |
|
Voltage |
220V or 110 V, 50/60Hz |
|
Fuse |
220V 3A , or 110V 6A |
|
Machine Power |
3500 W |
|
Package Size |
68cm*72cm*111cm+45cm*45cm*55cm |
|
Total Weight |
95kg |
|
Relative Humidity |
≤80% |
|
Atmospheric Pressure |
88KPa ～110KPa |
Our Service Advantages
Packaging and Delivery
We use standard export packaging, which includes a carton with an aluminum box. We maintain strict packing standards and offer various logistics solutions based on customers’ requirements to ensure that you can receive the goods as soon as possible.
Supply Ability
We have a strong production ability to meet your market needs. We have a professional R&D team and own the factory ourselves. All of the products are sold directly from the factory.
Lead Time
For standard products, 1-3 days for in-stock items and 3-7 workdays for out-of-stock items after payment. For customized products, the delivery time depends on specific circumstances.
FAQ
1. What services can we provide?
Our services include standardized product sales, customized production, overseas certification application, and OEM production.
2. What is the packaging of the product?
We use standard export packaging includes a carton with an aluminium box, and maintain strict packing standards to guarantee products’ integrity.
3. What kind of technical support do you provide?
We’ll reply within 12 hours after received the problem feedback, and for distributor, technical manuals, maintenance guide videos, online or on-site training can be provided.
4. How's the after-sales service?
We provide one-year free warranty and lifetime maintenance service.
